Main specifications

Table area

1,100 x 1,200

Maximum cutting pressure

Up to 120 Ton (Pressure 214kg/㎠)

Upper and Lower stroke distance

150/200/250/300 (MAX)( UNIT : mm )
Adjustable within maximum stroke distance

Maximum working hydraulic pressure

21Mpa (214 Kg/㎠ )

Hydraulic pump drive motor

11kw, 3ph, 6p (50 / 60 Hz)

Table Convey Method

Hydraulic cylinder or servomotor(optional)

Blade Height

H=20mm CANNOT BE USED

Guide Type

Sliding plate type

Feed table stroke distance

1,280 (UNIT : mm )

Machine Size

(W) 1,695 X (L) 3,900 X (H) 1,725

Machine Weight

About 6Ton

Hydraulic oil and lubricant

Terrace Oil #46 (ISO.VG46)

Hydraulic oil cooling method

Water cooled (250ℓ / MIN)

Base

anti-vibration rubber plate, horizontal type

Cutting plate

PE and etc

Operation start switch

Button switch

Blade Plate type

Thompson knife

Electricity and control

Electricity capacity

Approximately 12 kw

Main voltage

AC 220/380V (Overseas AC 380V)

Control panel and control box location

on the left of the main equipment

Photoelectric sensor for safety

1 optical axis

Options

Mold protection plate rotating device (device that rotates blade protection plate for longer use)
Feeder table servomotor control type (System which enables the feeder table's convey is controlled by a servomotor for accurate position, suitable for tasks using upper and lower molds)

TRACTION UNIT

WINCH HOPPER

SS400,12T&6TMM, 530L×344W×507Hmm

PINCH ROLLER

Φ126×404&Φ114×395Lmm, ROULLETE TYPE 2

BEARING UNIT

UCFS 209&UCT 206, UCFL204 etc, each 2SET

AIR CYLINDER

Φ25×45ST×2SET

GEARED REDUCER MOTOR

2HP, deceleration ratio 1/20, inch spped control using inverter (installed on electrical panel), CHAIN GEAR : 35NT&14NT

CRUSHING PART

rotation ROTOR

Φ250×280Lmm, 3deg 2BLOCKS

SHAFT

Φ75&Φ60mm, Specialty Steel

BEARING UNIT

Φ50&Φ45mm

rotation / precision

280L×6(etc)/280L×2(Front1+Rear1)

PULLEY&FLY-WHEEL

Φ305&240

FLANGE&DISK

2/each

BASE FRAME

SS400 6Tmm steel part, 840L×587W×450Hmm&mobility wheel5“×50B×4ea

Drive MOTOR

AC 220/380 V, 3 Phase, 6 pole HZ (102.75 KVA) High efficiency type

Electric PANEL

SIZE

600×500×250Dmm

Total capacity

9.5H.P(FEEDING MOTOR 2HP+CRUSHER 7.5HP)

INVERTER

SVG-TYPE, VOLUME METER, LS SYSTEM, SELECTOR SWIYCH(Continuous and 1 second operation)

Button

TO START/STOP BUTTON SWITCH, EMERGENCY(RESET BUTTON)

Device

A-METER, VOLT-METER, POWER LAMP

SHEET CONTROL UNIT

Usage

Pushes the scrap instantly after a forming is done and stops. Therefore, adjusting SCRAP TENSION brings forming scrap to for crush.

SIZE

770W×660L×970Hmm

Lower FRAME

125×65×8T E-CHANNEL 1

Upper support

75×40 E-CHANNEL

Pass holder

Φ50.8×725Lmm

WEIGHT BALANCER

Φ125×50Tmm×2

BEARING

UCFL205&6205ZZ each 2SET

Proximity SWITCH

PR-18AO×2 : By installing TIMER on an electrical panel, GEARED REDUCE MOTOR is stopped and starts after T seconds (continuous operation)

Machine Exterior

Size

1010L×700W×1410Hmm

Machine revolution speed

approx. 580 RPM

Machine color

Medium green

Machine Weight

About 650kgs

Main specifications

Cutting area

1200㎜

Cutting method

Table Convey Method.
When Pneumatic rodless cylinder moves left or right, the blade attached to the cylinder cuts the molds.

Product Receiver

Receives the cut pieces every cycle.
Stainless steel plate for flooring for the hygiene.

Machine Size

(W) 1,603 X (L) 1,700 X (H) 1945

Machine Weight

Approximately 500Kg

Base

Screw horizontal method

Operation start switch

Button switch (used according to forming machine)

Blade type

Heat-treated reinforced blade

Electricity and control

Electric capacity

within approx. 500W

Main voltage

AC 220/380V (Overseas AC 380V)

Control panel and control box location

The left of the main equipment